PSi3 Graphical ECU data monitor

10 August 2007, 08:55

A few more pictures of our latest monitor ...

Our latest monitor for 1999 - 2007 Subaru's combining features from our current monitors plus - EcuTeK User Tune and Map Switching functions, Road Dyno menu for 0-60, Standing quarter mile etc...

The following items can be displayed:-
Air flow meter
Advance Multiplier
Air Flow Voltage
Boost pressure
Battery
Charge temperature
Coolant temperature
Injector duty
Engine load
Engine speed
Exhaust gas temperature - requires additional sensors to be fitted
Air/Fuel Correction
Fuel pressure - requires additional sensors to be fitted
Injector duration
Ignition advance
Intake air temperature
Knock correction
Lambda sensor
Lambda sensor voltage
Oil pressure - requires additional sensors to be fitted
Oil temperature - Requires additional sensors to be fitted
Road speed
Rear oxygen sensor
Throttle position % (some cars have limited range e.g. 5 to 85 %)
User output 1
VVT Left
VVT Right
Wastegate Duty

Additional features:-
256 x 64 Graphical VFD display
Anti glare front panel
Peak data display
RPM and Boost in bar graph and numerical form
User defined display setup
User updateable software via PC
CANBUS and USB ready hardware
Custom Bitmap image upload and display
Plug and Play fitment
Water Injection / Nitrous control
Fault code reading and reset
ECU reset
Can be supplied with either Green or Blue display

User Tune functions:-
Overall ignition adjust
Ignition learning
Open loop fuelling
Boost pressure adjust
Wastegate duty
Variable valve timing
Idle adjust A/C off
Idle adjust A/C on
Engine rev limiter

User tune control for:-
Map Switch
Engine rev limiter

Track day functions:-
0-60 MPH
Standing quarter mile
Road dyno

1999 - 2001 Impreza/2001 - 2004 Forester Pod Mount £400

2001 - 2007 Impreza Pod Mount £400

1999 - 2007 Impreza Single DIN £375

2004 - 2007 Forester Pod Mount £480

All enclosures are genuine Subaru parts

All prices are plus delivery @ £8.50 and VAT.

These can be ordered direct from our website www.psi3.co.uk

email - sales@psi3.co.uk or call 07796 992 992

Pod mount in a Forester STi

10 August 2007, 10:19

Damn!!! Is there now way to get one of these for a 1998 WRX STi? This would be a lethal setup!!

10 August 2007, 10:34

can you answer a couple of question son these?

1) I am presuming these plug into the OBDII port - is there a OBDII port on the PSI3 that I could plug in my laptop to in order to datalog or some way of then downloading the logs from PSI3 to a laptop to analyse in Delta Dash?

2) Will you be adding a GPS option to enable lap timing?

10 August 2007, 12:24

Quote:

Originally Posted by shea2k

Damn!!! Is there now way to get one of these for a 1998 WRX STi? This would be a lethal setup!!

It may well work in your car, 1998/1999 was the change over period to full OBD II compliance, we know it works in the WRX STi5 from 1998, we offer a full refund if you purchase and find that the monitor will not work in your car.
Simon

10 August 2007, 12:44

Quote:

Originally Posted by dynamix

can you answer a couple of question son these?

1) I am presuming these plug into the OBDII port - is there a OBDII port on the PSI3 that I could plug in my laptop to in order to datalog or some way of then downloading the logs from PSI3 to a laptop to analyse in Delta Dash?

2) Will you be adding a GPS option to enable lap timing?

To answer your questions, yes they plug into the OBD port, output for datalogging capture is a planned feature for the near future, the monitors are supplied with a serial interface to connect to your pc/laptop for bitmap image download and software updates at present.

Lap timing is not a feature at present, the "Track Day" menu offers 0-60, quarter mile and road dyno options. Please see below user manual with the current features.
Simon

,

16 August 2007, 18:25

Any chance of a Group Buy on these?

16 August 2007, 20:34

Quote:

Originally Posted by drb5

Any chance of a Group Buy on these?

You have PM.
Simon

16 August 2007, 21:32

16 August 2007, 22:11

Oh could be most intrested in one of these if a group buy is going on them

Bandit

17 August 2007, 07:38

PSI3 GRAPHICAL ECU DATA MONITOR

17 August 2007, 07:51

Quote:

Originally Posted by PSI3

To answer your questions, yes they plug into the OBD port, output for datalogging capture is a planned feature for the near future, the monitors are supplied with a serial interface to connect to your pc/laptop for bitmap image download and software updates at present.

how near a future ?

17 August 2007, 09:44

Difficult to say at present, all of the new monitors have the have additional hardware already fitted for CANbus interface and data logging it's down to writing and testing the software.
Simon

13 September 2007, 14:24

Wow this is quite the bit of kit! Just having a quick read of the docs and posting so that I dont forget about this thread